 |
|
|
| |
Currently Chadwick T&T have four drilling rigs:
- ATS Rotary Auger Drill Rig mounted on a 4x4 land cruiser
- Description
- The rig was purchased new in 2004 and is suited to shallow geotechnical and environmental investigations.
- Dimensions
- Width: 2.1m
- Length: 5.5m
- Height (mast down): 2.5m
- Height (mast up): 7.6m
- Weight 2.2 tonnes
- Capacity
- Auger 8m – 100mm diameter
- SPT 8m
- Edson 100 Multipurpose Drill Rig mounted on a 4 x 4 truck
- Description
- The rig was purchased new in 2002 and is suited to geotechnical and environmental investigations. It is fitted with a high pressure pump.
- Dimensions
- Width: 2.2m
- Length: 6.5m
- Height (mast down): 3.1m
- Height (mast up): 5.7m
- Weight 6.0 tonnes
- Capacity
- Auger 30m – 125mm OD
- Hollow Auger 30m – 175mm OD
- Coring 100m – NMLC, NQ3, HQ3
- Rotary Mud 200m -70-150mm OD
- 70m - 250mm OD
- Down Hole Hammer 60m – 90mm OD
- SPT 30m
- Edson 200 Multipurpose Drill Rig mounted on a 4 x 4 truck
- Description
- The rig was purchased new in 2006 and is suited to geotechnical and environmental investigations. It is fitted with a high pressure pump.
- Dimensions
- Width: 2.2m
- Length: 6.5m
- Height (mast down): 3.1m
- Height (mast up): 5.7m
- Weight 6.0 tonnes
- Capacity
- Auger 30m – 125mm OD
- Hollow Auger 30m – 175mm OD
- Coring 100m – NMLC, NQ3, HQ3
- Rotary Mud 200m -70-150mm OD
- 70m - 250mm OD
- Down Hole Hammer 60m – 90mm OD
- SPT 30m
- Terrier Drill Rig mounted on rubber tracks
- Description
- The rig was purchased new in 2007 and is suited to geotechnical and environmental investigations. It is particularly suited to remote operation and restricted access.
- Dimensions
- Width: 0.8m
- Length: 2.7m
- Height (mast down): 1.5m
- Height (mast up): 2.85m
- Weight 1300Kg plus a 7000Kg retraction load
- Ground bearing pressure 33KPa
- Capacity
- Percussion Samples 10m
- Concrete Coring GL to 1m
- Dynamic Probing 30m
- SPT 30m
Drilling Equipment:
- High Pressure Cleaners
- Solid Augers 125mm OD x 30m
- Solid Augers 100mm OD x 10m
- Solid Augers 200mm x 3m
- Hollow Auger 175mm OD x 30m
- AW Drill Rods x 40m
- NQ Drill Rods x 36m
- HQ Drill Rods x 62m
- 76mm Hammer/Mud Rods x 200m
- Waterwell casing 200mm OD x 80m
- NQ casing x 36m
- HQ casing x 62m
- HW casing x 10m
- Coring NMLC, NQ3, HQ3
- 89mm Hammer / Mud Rods x 240m
- Down Hole Hammer 90mm
- Wash Boring Blade Bit 70, 90, 95, 130, 150, 250mm
- Rock Rolling 70mm, 100, 150mm
- Undisturbed Plastic Liner undisturbed percussion samples
- Undisturbed Samples 50 & 63mm
- Standard Penetration Test Sampler
- Concrete Corers – 80, 100, 150, 200mm
- Various pumps, water tanks and grouting equipment including grout pump
Support Vehicles
- Several four wheel drive support vehicles to back up the Drilling Rigs.
- 6 tonne Hino Truck with 1,000L water tank to back up the Drill Rigs.
- Single and tandem trailers to carry consumables and drilling equipment to site.
Licensing
- Currently have 3 Level 1 Licensed Drillers
Download our Terrier Rig Capability pdf (115kb)
Download pdf 
For more information please contact Mik Di Meglio. |
|
|
|
|
|
|
